Machines

OVERBECK Zetto 30

speed range workpiece 300, 600, 900 rpm, accuracy 0.003 mm, complete mechanical general overhaul in factory in 2017, mechanical condition as new

FISA VST 2000/P

mold cleaning for plastic injection molding, extrusion, elastomers, die casting, core boxes, molds; well-kept facility, was hardly in use

MEBA e-cut 400A

neat machine, without roller conveyors

Hwacheon Vesta 1050 B

filtration plant with coolant device AME HSP 350, band filter, coolant storage 2270 l; chip conveyor AME SB 200, without the pictured vises

Breunig IRCO Profimat 65.8/270.8

Guide tubes are changed automatically using a revolver/drum

MAG Ex-Cell-O XS211

High-speed machining center with horizontal main spindle, direct measuring systems in all axes, feed speeds X / Y / Z: 60 m / min., B: 60 1 / min, max.forces (X / Y / Z): 17.5 / 20 / 17.5 kN, main spindle (Weiss GmbH),hardly any operating hours, was only used for research purposes at a technical university

Wissner WiTEC 42 Economic

tool length scanning, spindel type: Reckerth Typ MSPF-125/36-12/FBLP/HSK-F40, frequency converter Berges Typ SWPK 400150 H12, vacuum pump Busch Typ RA 0255 D 502 Q0ZZ, industrial vacuum cleaner: Depureco Typ T22/100, cooling pump: company Chilly 25-5, the system was completely checked by Wissner service technicians

ABB IRB 2400/16 Type B - M2004

well-kept robot, usable immediately

WAGNER WMC 650

ALZMETALL AC 25

High-performance drilling machine, machine number 511

OTC Daihen Europe GmbH AC MIG 200 - CPDACR-200

with wire feed unit MIG CMWH-147 (Bj 2000) and control panel OTC Pro-Face, version hand power source

EMCO VMC 300

one tool station is currently defective, nice compact machine, can be used immediately

Bulleri Beta 6

Milling motor power 4 kW, vacuum pump 25 m³ / h, very good condition, immediately ready for use, servo motors in the axes, has run less than single-shift

VOEST / Weiler Alpine E50 / 2

swing diameter over cranking 600 mm, spindle head according to DIN 55027 size 8, inner cone: metr. 70 / 1:20, max. Torque 1200 Nm, quill taper MK5, quill diameter 70 mm

MAHO HANSEN HS 500E

checked by Maho technicians, ready for demonstration under power, instruction / training optionally possible

DECKEL FP 4A NC

less operating hours, can be inspected under power

Perkins 4012-46TAG3A

With continuous operation, the performance is reduced by 10%

Mysun Solar MSE-07 370 Watt Full Black

Solar module Maysun Solar, MSE-07 370 Wp - full black, mono PU module, 1755 mm x 1038 mm x 30 mm, length of connection cable 110 cm, collection only

Wicona 75EVO

Pneumatic press / punch, equipped with the following tools: 594 0008, 594 0038, 594 0006A, 594 0001A, 594 0022, 594 0019, 594 0013, turntable for quick tool change, stand consisting of: 504 0001 and 504 0003, from professional school, like new

D. Friedrich GmbH R100

very nice, well-kept machine, hardly any operating hours, with piece counter

D. Friedrich GmbH R100

very nice, well-kept machine, hardly any operating hours, with piece counter

Schlichter Profi Packer SCV-400 Plus

System structure: Magazine for elongated parts, conveyor belt, foil packaging machine, conveyor belt, shrink tunnel, roller conveyor. The system was used to weld in 2 m aluminum pipes (cycle 8 pieces/min.). Shrink tunnel: The speed of the roller conveyor and the power of the blower can be regulated. Film material: PVC polyolefine shrink film and polyethylene film

Roland SOLJET PRO4 XR-640

the left print head (A) needs to be replaced; print head and assembly cost € 3.000,00, can be tested under power

Expresso Balance Lift 060BLS655435

Gripper/lifter for tools or other parts. The part weight can be adjusted for lifting and lowering. Functions: lifting/lowering, gripping, swivelling, gripper holder 0.42 x 0.5 m

GDW RD250S

Lever quick-action collet chuck mounted on the main spindle via an intermediate flange. For deadlength collets type 173E. Otherwise in the standard version according to the original documents available, GDW lever with pushbutton for spindle start-up, GDW material stop mounted on the grooving slide behind the center of rotation, monitoring by Beru switch using actuating plunger. Plunger diameter 5.0 mm, 3-color ready light with functions: "locked" - "standby" - "operation", GDW set-up key holder for safely bridging the stop function, very well-kept machine from a workshop for the disabled, little used

Caterpillar C175-16 - Diesel

TRUMPF Handnibbler

hand-held, for cutting sheet metal

Allweiler LV25/6/130-U2 3D-W1

V no. A57408/00 centrifugal pump 4 m3/h, 400 V, 5,5 kW

SDMO X1250 TB

Documentation, heat exchanger, batteries, soundproof hood

MITSUBISHI

Böckmann Fahrzeugwerke GmbH H739

Trotec Laser 8005 Professional C1000

Type: Co² laser, controller RF 3000, laser Synrad evolution 100, laser power: 100W / 230VAC, lenses: 2.5" and 5", vacuum table with aluminum honeycomb support, processing area: approx. 1250 x 1250 mm, water cooling: cooling unit Neslab Merlin M100, JobControl software from Trotec 10.7.1

D. Friedrich GmbH N100

well-kept machine in top condition, with piece counter, riveting time adjustable, the specified rivet diameter applies to material ST 37

D. Friedrich GmbH N100

well-kept machine in top condition, with piece counter, riveting time adjustable, the specified rivet diameter applies to material ST 37

D. Friedrich GmbH N100

well-kept machine in top condition, with piece counter, riveting time adjustable, the specified rivet diameter applies to material ST 37

D. Friedrich GmbH N100

well-kept machine in top condition, with piece counter, riveting time adjustable, the specified rivet diameter applies to material ST 37

Baunataler Werkstätten AT

for cleaning of scrap electronics TYP 1 by means of compressed air, unhealthy dust can be removed by the suction system, volume flow at least 1000 to 15000 m³/h, can also be used for venting of picture tubes, retract height 850 mm, ball roller 920 x 1050 mm, diameter fresh air/extraction each 125 mm, diameter Ergo-grip 220 mm, incl. documentation, air connection 8 bar

D. Friedrich GmbH N100

well-kept machine in top condition, riveting time adjustable, the specified rivet diameter applies to material ST 37

D. Friedrich GmbH N100

well-kept machine in top condition, riveting time adjustable, the specified rivet diameter applies to material ST 37

D. Friedrich GmbH N100

well-kept machine in top condition, riveting time adjustable, the specified rivet diameter applies to material ST 37

D. Friedrich GmbH N100

well-kept machine in top condition, riveting time adjustable, the specified rivet diameter applies to material ST 37

Oemme s.p.a. P-20-V

for profile WICONA, system WICLINE 50E - 50EN, 60E, CODE:332.04.10, from vocational school, was hardly used, as new

Maschinenbau Weidemann Korbach

The turning device can hold 4 plastic bags (has been used to hold small parts of an injection molding machine). After reaching a certain quantity (impulse that the bag is full),the device continues to rotate by 90 °. Equipped with a motor and gear, as well as a sensor that triggers every 90 °, the control can be adjusted depending on the system, total height to bag top edge 980 mm, rotation speed 4.5 rpm, via another gear, the speed adjusted become.

AVK MTU 12V/4000

Not operational, cooling water is leaking from the fuel system (defective immersion sleeve).

SEIGER SLZ 500 E

without jaw chuck, contour calculation option and contour handwheel, Multifix mount, spindle head according to DIN 55027

MITSUBISHI

without exhaust system, without starter battery

ESS Schweißtechnik GmbH Transtig 231 / DC

with cooling, additional foot switch

Löwer KSM 2

BEHRINGER HBP 303A

automatic feed, piece counter, 2 m roller conveyor, good condition, can be used immediately

KEMPER

2 pcs. flexible suction arms, length 3 m, without wall mounting / Suspension

Thermal Technology 1000-4560-FP-20

High-temperature sintering furnace, max. temp. in argon approx. 1700 °C, in helium up to 2275 °C, the furnace was used for student/scientific purposes

IRCO ElektroVorschub

was attached to an EMCO lathe ET342

EMCO TURN 342

EMCO TURN 342

After pressing "Aux on" the machine switches off with error X/Z axis. Drives and amplifiers are ok. According to EMCO Service, the error comes from the setpoint specification of the driven tools. The error messages were probably not broken down in detail at the time.

KALTENBACH KKS 401 NA

fully automatic universal saw, workpiece stop for bevel cuts to the left and right, tool cabinet, work area lighting, CNC control cutting angle (DRNC),serial interface CC control, autom. Chip conveyor, discharge height 88 mm, rotary table in wear-resistant design, cut-off gripper with autom. Adjustment of the front gripper jaw, sorting device with drive, sorting 2 good parts, autom. Flat magazine FMA for stacks 1500 - 7000 mm with motor-driven roller conveyor T4, 6/12 m / min., 4 drag chains / 1 storage, magazine depth B1 = 1470 mm, storage depth 1000 mm, 18 compartments 136 mm, 2 compartments 212 mm, automatic gate , bar storage for material pre-storage, depth 700 mm, multiple allocation

GREIF DV 30-2-2U

good condition

SAMECA Monosam D32 - SAM 32

Guide tubes 10 and 25 mm, was attached to an EMCO lathe ET242

Eimeldingen HG 10 - 1250 / D30M

Connection for built-in rotary encoder, connection for built-in reference switch/limit switch. Rotary table is driven by a three-phase motor, left/right rotation, manual clamping, table was used exclusively for test purposes, table surface with T-slots 22-H12 DIN 650, degree scale/ruler around the table

Rische + Herfurth Polystar 601M

Heating element opening 15 mm, weld seam length 600 mm, passage width 525 mm, weld seam width 3 mm

BEHRINGER KS 200 HY

good condition

Albis / Weidemann TWDM 8+15/40

Dimensions see picture / drawing, height + inclination adjustable, splitted band, height of cleats 15 mm, splitting of cleats 300 mm

PLANK FSP 50

Albis / Weidemann TWDM 8+15/40 TR 1230

Dimensions see picture / drawing, height + inclination adjustable, height of cleats 15 mm, splitting of cleats 300 mm

Dixie Union Verpackungsmaschinen MODULAR

PA / PE film packaging / paper packaging e.g. for medical products with soft blister printing on clichés, machine was in use until dismantling

IRCO ElektroVorschub

was attached to an EMCO lathe ET342

WÖRNER AGE 10

well-maintained machine ready for immediate use

FORKHARDT DSE

Separate control device for the chuck clamping

HERMLE UWF 720

under power, ready for inspection

Häberle HK 6

Miter, automatic pneumatic tension

Reutlinger RS 12 863

maintained vibration meter

EISELE VMSIIPVPR.072

semi-automatic machine, electrical limit stop, automatic cutting cycle, pneumatic clamps, prepared for pneumatic controlled supply

PEHAKA HS340

semi-automatic operation, robust machine, good condition, ready to use

JOISTEN + KETTENBAUM P6

arm 350 mm, with cooling, welding time adjustable, U = 1,2 - 2,2, Fr. 50, input one phase 220 V, I = 29 A

VDF - HEIDENREICH & HARBECK 18 RO

Meister Craft MTS 1000

circular saw for wood/plastic, table/cabinet made of aluminum profiles, under table with door, stop/guide

EMCO Zubehör

Kreuzer

measuring table respectively laboratory table with a granite plate and a thereon permanently bonded aluminium plate with base frame, aluminium plate with threaded holes M8, hole spacing 50 mm

MIVESA - das Original

Size C, Location hole for Multifix on the support, diameter 23 mm

LOEWE

3R 3Refix 3R-935-56.40 02

Reference table/Clamping field, holes with M12 thread, bores diameter 16/12 m, bores diameter 11/18 mm, No. 3R-935-56 02, SN 400 100

MITUTOYO B-706

complete set transport cecurity for coordinate measuring machine B-706, device can be rented against deposit amount of 1000 Euro.

Maschinenbau Weidemann Korbach

The turning device can hold 4 plastic bags (has been used to hold small parts of an injection molding machine). After reaching a certain quantity (impulse that the bag is full),the device continues to rotate by 90 °. Equipped with a motor and gear, as well as a sensor that triggers every 90 °, the control can be adjusted depending on the system, total height to bag top edge 980 mm, rotation speed 4.5 rpm, via another gear, the speed adjusted become.

GMN TSAV 160 x 630

Machine spindle for belt drive and direct drive, 2500 rpm, overhauled in 03/03 and no longer used, original packing from GMN, serial no. 280217, used, in full function

Ludwig & Fries

Ludwig & Fries

roller burnishing chair to finish shafts